www.ledex.com.au

CB36L: Low Power Input, 36-Units — $2,200.00
CB36L has individual high-power charging circuit board for each charging unit. It is connected to 24 VAC and distributes this low power to all charging units directly. The back panel can be opened for services.

VC3: Video Light, Camera Light & Trval Light — $175.00
Sunlight colour temperature. Even light distribution without any spots or scatters. Three level illuminations in 2-LEDs,8-LEDs or 10-LEDs on. Rechargeable lithium battery for 15 hour operation in all LEDs on to significantly save your long term cost. Extremely long operation more than 15 hours. Fully sealed structure in waterproof, dustproof and impact resistance. Light weight, small size and compact - very easy to use and carry. Rich accessories for various extremely convenient applications.

Operating modes — $110.00
Rigorous: Rigorous enclosure casing with elastic surface treatment for superior impact-resistance and anti-corrosion;. Secure: Single-bodied explosion-proof barrier, tight structure for dust-proof and waterresistance, effective battery with over-charging and over-discharging protection. Low maintenance: Easy to clean; no bulb to check or change, no repairing;. Low Total-Cost-Ownership: Long LED lifetime without bulb to change,no batteries to replace, no maintenance, no running cost;. Bright:...

KL8: Traditional Style LED Caplamp — $165.00
Small volume & light weight: Significantly reduced weight than lead-acid caplamp. Long life light source: Large power LED lamp-housing and effective heat dissipation design. Average LED life time is 50000 hours. So never worry about light source replacement. Minimal maintenance: no daily maintenance required. Significantly reduced the Cost of Ownership. Extraordinary safety: no leaking, no erosion, no pollution, no heat. Power display: Three mini red LEDs display the power situation. Long operation...

CB52: Mains Input with RCBO & Step-Down Transformer, 52-Units — $3,850.00
CB52 has individual low-power charging circuit board for each charging unit. A built in power supply generates 12VDC power for charging units. A panel mount RCD sits between the 240VAD mains power input and the power supply for personal protection. This low power distribution to charging units makes it very safe and suitable for mining applications. Front panel can be opened and locked for convenient service.

CB36: Mains Input with Online RCD, 36-Units — $2,200.00
CB36 has individual high-power charging circuit board for each charging unit. It is connected to the 240VAC main power and distributes the main power to all charging units directly. A RCD power plug on power cord is used for personal protection. The back panel can be opened for services.

KC2S: Lightweight with Single LED — $154.00
KC2S is a lightweight model. Its light weight, focused beam and low cost make it suitable for rescue and firefighting operations and industrial applications.

CB53E: Mains Input with RCBO & Step-Down Transformer, 53-Units, for KC3E/KH3E — $5,390.00
There is a padlock bracket under each charging unit. The KC3E can be padlocked to this bracket through the lamp clip. It is suggested you padlock the caplamp whenever leaving it plugged in. It is recommended that mines use the Charging Bank as the only charging facility so that if a lamp is stolen it cannot be recharged. The individual chargers are intended for individual use only. For the CB53E, the charging units in upper 4 row place locks under the caplamps. The charging units in lower...

KH3TP: Traffic Control Portable Lamp and Headlamp — $209.00
Handheld: Simply hold in hand as a torch or a portable signal light. Head Strap: Worn either on the head using our Head Strap or on a hard cap using our Cap Strap, or directly fitted onto a miner’s helmet. It also cab be worn on one side of the helmet using our Side-Mount Bracket. Belt wearing: Wear the lamp on the belt using our Belt Bracket. Fixed location: Clamp the lamp to an object or attach it to metal using our Magnetic Clamp Bracket. Mobile location: Quickly install the lamp anywhere...

LC2I: Bobby Dazzler - Farmer's Lamp — $200.00
Whenever you work outdoors at night, no doubt you would wish to have powerful and hands-free lighting, just as an underground miner uses his Caplamp. Certainly up till now, the heavy battery pack carried at the side on your belt, the clumsy, snagging, electric cable, complex routine maintenance, special charging facility requirements and extremely high cost made it impossible for any farmer to dream of being able to use such a Caplamp. However, now your dream can become a reality, thanks to...

KC3R: Side-Worn with Rear Beacon — $275.00
Four operating states can be toggled by pressing the button switch. From the OFF condition, pressing the button turns the lamp ON to whatever condition it was in when turned OFF. Pressing the button again will now toggle to the next mode of operation. At any time, pressing the button and holding it for two seconds will turn the lamp OFF.

KC4S: Side-Worn with High Capacity and a High Power LED — $462.00
The bracket is adjustable in left-right direction to set a distance from the helmet so other attachments such as a visor will not block the light. The lamp is also angle adjustable in the forward-back direction to set the light projecting direction. Using the both bracket and lamp adjustments, all-around angle is achieved.

CB8D: Dual Power Input, 8-Units — $633.00
Powered by either main power of truck cigarette lighter. Powered by low voltage DC. Compact and light weight. Easy to carry. Easy to install in a truck.

KC3D: Standard Model with dual LEDs — $231.00
No electric cord can be bumped or tangled;. Significantly reduces miner’s burden;. No back pain and injury any more;. No acid or toxin to spill;. No heat on lens surface; No burnable parts to cause fire;. IP67 case for the harshest mining environment;. As a warning lamp to wear on your back or attach to an object.

KC3S: Single LED Model — $210.00
The LED works in three illumination levels for different brightness and durations. Pressing the button switch toggles operating modes in the following order: off --> level 1 --> level 2 -->level 3.

KH3VS: Vehicle Emergency Lamp and Headlamp — $198.00
Head lamp: Worn on either the head using our Head Strap a simple hard cap using our Cap Strap. Torch: Simply hold in hand as a torch. Our Wrist Strap can help secure the lamp. Belt wearing: Use our Belt Bracket to wear the lamp on the belt. Fixed location: Use our Magnetic Clamp Bracket to clamp the lamp to an object or attach the lamp to metal. Frequently used location: Screw or glue our Lamp Brackets to a place where you use the lamp often, then fit the lamp on it. Mobile location: Use our...

KC2M7: Lightweight with 7 LEDs & Individual Focusing Reflectors — $154.00
KC2W is a lightweight model in 7-LEDs. Every LED has an individual concave reflector so a well focussed beam and well distributed light pattern can be achieved without any shadow. It also features a longer operation and low cost suitable for various industrial applications.

CHARGING ACCESSORIES — $66.00
Charge the lamp from the cigarette lighter in a car (12VDC) or a truck (24VDC). A LED indicates the charging process. This charger is optional.

LC2.5I: Low Cost Industrial Model with 10 LEDs in Flush Light — $200.00
LC2.5I is designed to I.S. specifications for coal mine certificate from overseas, but not certified in Australia and therefore the cost is significantly reduced, while keeping the same structure, rigidity, IP rating, brightness and duration. A good option for open-cut mines, tunnels and work-shops when I.S. certificate is not needed, cost is a consideration and lower level of luminous intensity than standard miner’s caplamp is acceptable.

KS2xy: Portable Multi-Functional Safety Lamps — $231.00
KS2xy is a very flexible model. It has two colors to choose from. "xy" specifies colors. Default type is KS2rb in Red and Blue; but you can specify other colors in orders using "xy". LEDs can be in stable 10-LEDs on for best signal strength, or flashing 4-LEDs on for long operation and better visual effect. With these flexible options, there are 5 operating modes available.

CB35E: Mains Input with Step-Down Transformer, 35-Units, for KC3E/KH3E — $3,850.00
There is a padlock bracket under each charging unit. The KC3E can be padlocked to this bracket through the lamp clip. It is suggested you padlock the caplamp whenever leaving it plugged in. It is recommended that mines use the Charging Bank as the only charging facility so that if a lamp is stolen it cannot be recharged. The individual chargers are intended for individual use only. For the CB53E, the charging units in upper 4 row place locks under the caplamps. The charging units in lower...

CA: Charging Adaptor — $13.00
Charging Adaptor can be used to charge our lamps on a traditional Lead Acid Charging Rack. It converts the charging rack output into charging electricity in our lamp charging specification. We encourage mines to use Charging Banks, rather then keeping the old Charging Rack. However, as a temporary solution, Charging Adaptors can be used in introduction period to build your confidence in lamps.

CB8S: Charging Shelf with a Panel and an 8-Way Power Board — $165.00
CB8S does not have any charging circuit. Eight mains outlets are mounted on the shelf so lamp Mains Chargers can be plugged in. Lamps are hooked on the panel with charger wires hiding behind the shelf to make the arrangement tiny. Four chambers can be used to store accessories and other things. This equipment uses your existing chargers to save you costs while still realizing centre management for lamp charging. It is suitable for small mines, CPPs, workshops or any small teams using cordless...

KC3E: Standard Model in External Charging with dual LEDs — $255.00
No electric cord can be bumped or tangled;. Significantly reduces miner’s burden;. No back pain and injury any more;. No acid or toxin to spill;. No heat on lens surface; No burnable parts to cause fire;. IP67 case for the harshest mining environment;. As a warning lamp to wear on your back or attach to an object.